| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
zram: fix out-of-bounds access in read_block_state()
read_block_state() calculates nr_pages before taking dev_lock. If the
device is reset and reinitialized with a smaller disksize before lock
acquisition, nr_pages still describes the old table. The subsequent loop
can then call slot_lock() past the end of the newly allocated table.
Read disksize after acquiring dev_lock and checking that the device is
initialized. The read lock then keeps the table and its bound stable for
the duration of the scan. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: picolcd: clamp eeprom debugfs read to bytes actually received
picolcd_debug_eeprom_read() trusts resp->raw_data[2] -- a length byte
supplied by the device in its REPORT_EE_DATA reply -- clamped only to
the caller's read() count:
ret = resp->raw_data[2];
if (ret > s)
ret = s;
if (copy_to_user(u, resp->raw_data+3, ret))
It never checks resp->raw_size, the number of bytes picolcd_raw_event()
actually copied into the 64-byte raw_data[] of the kmalloc'd struct
picolcd_pending. A device (or a spoofed picoLCD) returning a length byte
of 0xff, read with a count >= 255, makes copy_to_user() read past
raw_data[] into adjacent slab memory and return it to userspace through
the debugfs "eeprom" file:
BUG: KASAN: slab-out-of-bounds in _copy_to_user
Read of size 255 ... picolcd_debug_eeprom_read+0x214/0x2f0 [hid_picolcd]
The debug-dump path in the same file already validates the device length
byte against the received size before trusting it; this read does not.
The file is created S_IRUSR (root-only) and a crafted device is needed,
so it is neither unprivileged- nor remotely-triggerable.
Clamp the copy length to resp->raw_size - 3 (the payload actually
received, minus the 3-byte header), floored at 0 for short replies. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: serial-u16550: Check card index validity at probe
serial-u16550 driver blindly trusts that the given devptr->id value is
within the proper card index range at probe. It's OK for the devices
the driver itself creates at the module probe time, but if the device
is bound manually via sysfs interface, this could be -1 as "none", and
this leads to OOB access for index[] and other parameters.
Add a sanity check for the card index and warn/correct it if it's a
value out of the range. |
| Netty is a network application framework for development of protocol servers and clients. In netty-codec-haproxy prior to versions 4.1.135.Final and 4.2.15.Final, when decoding a PP2_TYPE_SSL TLV, HAProxyMessage.readNextTLV() first calls `header.retainedSlice(header.readerIndex(), length)` and only then reads the 1-byte client field and 4-byte verify field. If the attacker sets the TLV length below 5, the subsequent readByte/readInt throws IndexOutOfBoundsException. HAProxyMessageDecoder only catches HAProxyProtocolException around this call, so the IOOBE propagates and the retained slice on the pooled cumulation buffer is never released. Versions 4.1.135.Final and 4.2.15.Final patch the issue. |
| OpenEXR is the reference implementation and specification for the EXR image format, widely used in the motion picture industry. OpenEXR versions 3.2.0 through 3.2.10, 3.3.0 through 3.3.12, and 3.4.0 through 3.4.13 are vulnerable on ILP32 builds to a heap out-of-bounds read. The issue occurs when a crafted RLE-compressed EXR causes the 64-bit unpacked size to truncate before allocation in OpenEXRCore decoding.c and unpack_32bit() reads beyond the resulting buffer, allowing denial of service. This issue is fixed in versions 3.2.11, 3.3.13, and 3.4.14. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - copy IV using skcipher ivsize
AF_ALG rfc3686-ctr-aes-ccp requests pass an 8-byte IV to the driver.
ccp_aes_complete() restores AES_BLOCK_SIZE bytes into the caller's IV
buffer while RFC3686 skciphers expose an 8-byte IV, so the restore
overruns the provided buffer.
Use crypto_skcipher_ivsize() to copy only the algorithm's IV length. |
| In libxml2 before 2.15.4, there is a heap-based buffer overflow in xmlXPtrEvalXPtrPart because of xmlXPtrEval xpointer length saturation. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: validate option length before reading conf opt value
l2cap_get_conf_opt() derives the option length from the
attacker-controlled opt->len field and immediately dereferences
opt->val (as u8, get_unaligned_le16() or get_unaligned_le32(), or a
raw pointer for the default case) before any caller has confirmed
that opt->len bytes are present in the buffer. The callers
(l2cap_parse_conf_req(), l2cap_parse_conf_rsp() and
l2cap_conf_rfc_get()) only detect a malformed option afterwards, once
the running length has gone negative, by which point the
out-of-bounds read has already executed.
An existing post-hoc length check keeps the garbage value from being
consumed, so this is not a data leak in the current control flow. It
is still a validate-after-use ordering bug: up to 4 bytes are read
past the end of the buffer before it is known to contain them, and it
is fragile to future changes in the callers.
Fix it at the source. Pass the end of the buffer into
l2cap_get_conf_opt() and refuse to touch opt->val unless the full
option (header + value) fits. Each caller computes an end pointer
once before the loop and checks the return value directly instead of
inferring the error from a negative length. |
| In rsync 3.0.1 through 3.4.1, receive_xattr relies on an untrusted length value during a qsort call, leading to a receiver use-after-free. The victim must run rsync with -X (aka --xattrs). On Linux, many (but not all) common configurations are vulnerable. Non-Linux platforms are more widely vulnerable. |
| In the Linux kernel, the following vulnerability has been resolved:
mfd: cs42l43: Sanity check firmware size
Currently the code checks if a firmware was received, however it does
not verify that the firmware size is larger than the firmware header. As
the firmware pointer is dereferenced as a pointer to the header
structure this could lead to an out of bounds memory access. Add the
missing check. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/percpu-km: fix bitmap overflow and accounting in pcpu_create_chunk()
In pcpu_create_chunk(), nr_pages is the total contiguous backing
allocation, i.e., nr_units * pcpu_unit_pages, but pcpu_chunk_populated()
uses it to set chunk->populated, whose size is pcpu_unit_pages, bitmap.
Since bit N in chunk->populated means page offset N inside every unit is
backed. When nr_units > 1, the function writes beyond chunk->populated.
Fix it by using chunk->nr_pages.
It also fixes the global pcpu_nr_empty_pop_pages accounting, since
pcpu_balance_free() only iterates up to chunk->nr_pages.
Commit a63d4ac4ab609 ("percpu: make percpu-km set chunk->populated bitmap
properly") introduced the bitmap overflow issue. Later, commit
b539b87fed37f ("percpu: implmeent pcpu_nr_empty_pop_pages and
chunk->nr_populated") added pcpu_nr_empty_pop_pages and caused the
accounting issue. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/test: Fix __fortify_panic
Fix a runtime assertion in setup_xor_mapping(). Fortify complains that it
is potentially overflowing the xormaps array per __counted_by(nr_maps).
Quiet the false positive by initializing @nr_maps earlier.
memcpy: detected buffer overflow: 32 byte write of buffer size 0
WARNING: lib/string_helpers.c:1036 at __fortify_report+0x4d/0xa0, CPU#8: modprobe/2728
Call Trace:
__fortify_panic+0xd/0xf
setup_xor_mapping+0x6c/0xa0 [cxl_translate]
[ dj: Fixed up @nr_entries to @nr_maps in commit log. ] |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-qpic-snand: write the feature value before executing SET_FEATURE
qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits
the descriptors, which makes the controller execute the command
immediately. For SPINAND_SET_FEATURE the value to be written is only
placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a
second submission - so the chip is programmed with whatever that register
happened to hold from a previous operation, and the intended value is only
applied by the *next* SET_FEATURE.
Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing
0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the
subsequent write of 0x00 leaves it at 0x40 - every write lands one
operation late.
This stayed unnoticed until v6.18 added SPI-NAND OTP support together
with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode,
reads, and disables it again, and mtd_otp_nvmem_add() does this during
MTD registration. With the off-by-one, the "disable" write actually
applies the previously requested value, so CFG_OTP_ENABLE ends up set:
the chip stays in OTP mode, every subsequent array read returns the OTP
area instead of the array (UBI reports an empty device) and all writes
fail with -EIO because the OTP area is write protected. On this board
that makes the whole flash unusable and the device unbootable.
Write the feature value into NAND_FLASH_FEATURES as part of the same
transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the
operation actually carries - the previous code dereferenced a 4-byte
pointer on a one-byte buffer (spinand->scratchbuf).
With this patch the flash contents read back bit-identical to a
known-good dump of the same board taken under the vendor firmware
(md5-verified across partitions), and writes work. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: validate individual TWT params before driver setup
ieee80211_process_rx_twt_action() only partially validates a received
S1G TWT setup frame before queueing it.
An individual agreement can therefore reach ieee80211_s1g_rx_twt_setup()
with twt->length too short for the full struct ieee80211_twt_params.
The individual path passes twt to drv_add_twt_setup(). Both the tracepoint
and the driver callback consume the complete parameters block, not merely
req_type. Do not pass a short individual agreement to the driver.
Broadcast agreements remain unchanged because they are rejected locally
after accessing only req_type.
[edit commit message to not overclaim lack of validation nor
understate driver impact] |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate Adaptation Indication parameter length
The Adaptation Layer Indication parameter contains a fixed 32-bit
Adaptation Code Point after its parameter header. However,
sctp_verify_param() accepts a header-only parameter because the generic
parameter walker only requires the header to be present.
sctp_process_param() then reads adaptation_ind beyond the declared
parameter. When the malformed parameter is last in an INIT, the read
starts at the receive skb tail, and the value is copied into the state
cookie returned in the INIT ACK. This may disclose four receive-buffer
tail bytes.
Require the declared parameter length to match the fixed structure size
and abort the association through the existing invalid parameter length
path otherwise. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Improve EP11 CPRB domain handling with ASN.1 parsing
The zcrypt_msgtype6_send_ep11_cprb() function uses fragile struct
overlays to access and modify the domain field in the EP11 CPRB
payload, creating maintainability and security concerns:
1. Struct overlay approach (pld_hdr) assumes fixed payload structure
and doesn't validate the actual ASN.1 encoding.
2. Complex length format detection logic is error-prone and doesn't
properly validate bounds at each parsing step.
3. Direct struct member access bypasses proper ASN.1 validation.
Fix by replacing struct overlays with explicit ASN.1 parsing that
validates each field (payload tag/length, function tag/length/value,
optional domain tag/length/value) with proper bounds checking at every
step. Add asn1_int_encode() helper function to safely write integer
values with correct endianness conversion. This makes the code
consistent with the validation pattern introduced with the rework of
the xcrb_msg_to_type6_ep11cprb_msgx() function. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/pseries: papr-phy-attest - validate cmd.length, plug mem leak
In papr_phy_attest_create_handle(), the params->cmd.length is not
validated before use, which can result in a buffer overlow. Check it and
return -EINVAL if it is either 0 or exceeds sizeof(params->cmd).
Also, params is freed on the success path but not error. Free it on
errors after memory allocation. And free it on negative fd. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - zero report size on F54 work error
In rmi_f54_work(), if an error occurs during report request or command
verification, the code jumped directly to the 'error' label, bypassing
the 'abort' label where f54->report_size was normally zeroed out.
This left f54->report_size containing its previous successful payload
size. If a user then altered the V4L2 format to a smaller size, and a
subsequent run failed, rmi_f54_buffer_queue() would copy the stale,
larger payload size into the shrunken V4L2 buffer, causing a heap
buffer overflow.
Fix this by merging the 'abort' and 'error' labels into a single 'out'
exit path, and ensuring that f54->report_size is always set to 0 on
failure by checking for error and zeroing the local report_size first. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate cookie AUTH state before use
When cookie authentication is disabled, COOKIE_ECHO restores fixed-size
AUTH fields directly from peer-controlled cookie bytes. A forged RANDOM
length, HMAC list, or CHUNKS list can then reach association consumers
with lengths or identifiers that were never validated against the local
backing arrays.
A forged RANDOM length can cause out-of-bounds reads during key-vector
construction. A forged HMAC identifier also caused a 32-byte write past
a zero-length AUTH chunk, providing a primitive for a local privilege
escalation chain.
Validate the cookie's RANDOM, HMACS, and CHUNKS parameters at the cookie
trust boundary before copying them into the association. Reject invalid
types, malformed lengths, unsupported HMAC identifiers, HMAC lists
without SHA1, and forbidden chunk ids. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: misc: usbio: check ibuf_len against rxbuf_len in bulk msg
ibuf_len is the bulk IN (receive) buffer size, but the EMSGSIZE check
in usbio_bulk_msg() compares it against txbuf_len — the bulk OUT
endpoint size. Both are taken independently from different endpoints
in usbio_probe(), so the check is wrong when they differ.
Use rxbuf_len for the IN direction. This matches the buffer that
actually holds the response data. |
