| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject a tree connect response whose byte count is too small
CIFSTCon() bounds its strnlen() over the byte area with the server's
ByteCount minus two, which for ByteCount 0 or 1 goes negative as an int
and converts to a huge size_t. The later subtraction wraps the __u16
bytes_left, and that is what bounds cifs_strndup_from_utf16(): a bound of
up to 65535 against a ~16 KB cifs_req_poolp object runs off the end of the
slab object, and the bytes reach userspace through tcon->nativeFileSystem
in /proc/fs/cifs/DebugData.
Reject a byte area too small for what the parser consumes. Two bytes is
the least it can consume, and no conformant response carries fewer. The
new trace point is the 129th smb_eio_trace entry, which __mode(byte)
cannot represent, so the attribute goes with it. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: restore the data_offset bound in is_valid_oplock_break()
Commit 83bfbd0bb902 ("cifs: Remove the RFC1002 header from smb_hdr")
changed the quantity this bound is measured against. It used to be
srv->total_read minus the 4-byte RFC1002 preamble that total_read then
included, so it was the SMB message length. The same commit stopped
counting the preamble, and the mechanical substitution to
srv->total_read - srv->pdu_size left an expression that is identically
zero: standard_receive3() reads MID_HEADER_SIZE() bytes and then exactly
pdu_length - MID_HEADER_SIZE() more, adding both to total_read.
len is therefore 0, the subtraction below it wraps, and no __u32
DataOffset can exceed the result, so the check from commit 097f5863b1a0
("cifs: read overflow in is_valid_oplock_break()") no longer rejects
anything. Use total_read, which is now the message length on its own. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: sensor: custom: Fix field sysfs group cleanup on failure
hid_sensor_custom_add_attributes() creates one sysfs group for each
custom sensor field. If sysfs_create_group() fails after some groups
have already been created, the function returns the error without
removing the previously created groups.
Add a local unwind path to remove the groups that were already created.
With enable_sensor exposed only after the field attributes are ready,
this path can free sensor_inst->fields without leaving enable_sensor
able to access pointers into that array. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: universal-pidff: stop the device when force-feedback init fails
universal_pidff_probe() starts the device with hid_hw_start() and then, if
force-feedback initialisation fails, returns the error through a label that
only does "return error". The device is left started.
The HID core does not unwind on the driver's behalf. __hid_device_probe()
releases the devres group, closes the report and clears hdev->driver:
if (ret) {
devres_release_group(&hdev->dev, hdev->devres_group_id);
hid_close_report(hdev);
hdev->driver = NULL;
}
The hidraw character device that hid_hw_start() registered through
hid_connect() is allocated with kzalloc() and added with cdev_device_add(),
so it is not devres-managed and survives that. With hdev->driver NULL,
hid_device_remove() skips hid_hw_stop() as well, because it only unwinds
while a driver is still attached. The registration therefore outlives the
device on both paths.
Opening the surviving /dev/hidrawX writes into freed memory. KASAN reports
a use-after-free write from hidraw_open() -> hid_hw_open() -> the
transport's open callback, which takes a spinlock inside the freed object.
A descriptor that carries a PID usage page and no input reports is enough:
hidraw claims the device so hid_hw_start() succeeds, while hid->inputs
stays empty so force-feedback init fails. The other failure returns in
hid_pidff_init_with_quirks() - no output reports, an allocation failure,
pidff_init_fields(), pidff_check_autocenter(), an unusable effect count,
input_ff_create() - all reach the same label.
Stop the device on that path. hid-dr.c and hid-emsff.c, which start the
device with the same HID_CONNECT_DEFAULT & ~HID_CONNECT_FF mask, already do
this. The two earlier gotos must keep returning without hid_hw_stop(),
since neither has a started device, so give the path that fails after the
start its own label.
Discovered by XBOW, triaged by Baul Lee <[email protected]> |
| In the Linux kernel, the following vulnerability has been resolved:
HID: mcp2221: clear rxbuf after I2C/SMBus transfer completes
mcp_i2c_smbus_read() stores the caller-supplied buffer pointer in
mcp->rxbuf for the duration of a transfer but never clears it when the
transfer finishes or times out. Once the caller frees or reuses the
buffer, mcp->rxbuf becomes a dangling pointer. A delayed or spurious
MCP2221_I2C_GET_DATA report can then drive mcp2221_raw_event() to
memcpy device data into the freed memory, causing a write
use-after-free.
Route all return paths through a single exit point that clears
mcp->rxbuf and mcp->rxbuf_size, so that the existing !mcp->rxbuf guard
in the raw_event handler can reject any report arriving after the
transfer has ended. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: intel-thc-hid: intel-quickspi: validate report size before copy
write_cmd_to_txdma() builds an output report in qsdev->report_buf, a heap
buffer allocated in quickspi_alloc_report_buf() to the device-descriptor
derived max_report_len (a few hundred bytes for a touch controller). It
copies the caller-supplied report into that buffer:
memcpy(write_buf->content, report_buf, report_buf_len);
The HID core caps a report at HID_MAX_BUFFER_SIZE (16384) by default, and
quickspi_hid_ll_driver does not set max_buffer_size, so the length reaches
the driver unbounded. A hidraw SET_REPORT/SET_FEATURE ioctl carrying a
report larger than max_report_len therefore overflows report_buf with
attacker-controlled length and content.
Record the report_buf allocation size and reject reports that do not fit
before copying, matching the equivalent guard in the intel-quicki2c
sibling (quicki2c_init_write_buf()) and the hid-goodix-spi fix.
write_cmd_to_txdma() writes the output report header ahead of the content
in the same buffer, so size the allocation to cover the header as well.
That keeps the added bound from rejecting a maximum-sized report. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: intel-thc-hid: intel-quickspi: bound GET_REPORT response to the caller buffer
quickspi_hid_raw_request() receives the caller's buffer length in len, but
quickspi_get_report() never sees it and copies the whole device-supplied
response into buf regardless:
memcpy(buf, qsdev->report_buf, qsdev->report_len);
qsdev->report_len comes from the input report the touch controller returns,
while buf is sized to whatever the caller asked hidraw for through
HIDIOCGFEATURE or HIDIOCGINPUT. A response larger than that overflows buf
with device-controlled content.
The intel-quicki2c sibling already passes the caller length down to
quicki2c_get_report() and validates the response against it before the
copy. Do the same here. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: validate dirty page table on log replay
Each DIR_PAGE_ENTRY ends in a page_lcns[] array whose length is the on-disk
lcns_follow field. check_rstbl() validates the table bookkeeping but never
checks that this array fits in the entry, so a crafted lcns_follow lets the
v0->v1 conversion memmove and later replay passes run off the entry.
Add check_dp_table() to reject, right after check_rstbl(), any entry larger
than its size claims via struct_size() (the same expression used to allocate
these entries, so the check is overflow-safe by construction). All consumers
can then trust lcns_follow as the real capacity. This covers every
page_lcns[] access whose index is bounded by the entry itself (the
conversion memmove, the HotFix store via find_dp(), and the self-bounded
scan loops). Accesses whose index comes from the log record need a separate
bound and are handled in a follow-up patch. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: fix info-leak on partial LZNT decompress in ni_read_frame()
ni_read_frame() decompresses an LZNT $DATA frame into the vmapped target
pages and then trusts decompress_lznt()'s return value:
unc_size = decompress_lznt(frame_ondisk, ondisk_size, frame_mem,
frame_size);
if ((ssize_t)unc_size < 0) err = unc_size;
else if (!unc_size || unc_size > frame_size) err = -EINVAL;
decompress_lznt() stops as soon as the compressed stream is exhausted
(e.g. a zero chunk header) and returns the number of bytes it actually
wrote, which may be far less than frame_size. The bytes between unc_size
and frame_size are never written. The only memset() that follows zeroes
the region beyond i_valid; when the frame lies entirely within the file's
valid size that memset() does not run, so the gap retains whatever was in
the just-vmapped pages. All pages are then marked uptodate and returned
to userspace, disclosing uninitialized (recently-freed) kernel page
memory. A crafted compressed file whose stream decompresses to only a few
bytes leaks the remainder of every frame on a plain read(2), which is
enough to recover kernel pointers and defeat KASLR.
Zero the [unc_size, frame_size) tail immediately after a successful LZNT
decompress so the remainder reads back as zero. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: bound page_lcns[] index by the log record
The copy_lcns loop and the redo shorten loop index page_lcns[] at j + i,
where i runs up to the log record's lcns_follow. That count is checked only
against the record's own length, not the target entry, so check_dp_table()
(which validates the entry's lcns_follow) does not cover it: the copy_lcns
entry may even be freshly allocated after that check, and find_dp() bounds j
but not i. A crafted record thus overflows page_lcns[] of an otherwise valid
entry.
Add dp_range_ok() and reject, before each loop, any record whose run does
not fit the entry. These are the only two page_lcns[] accesses indexed by
the record rather than the entry, so together with the entry validation
every access is now bounded.
[[email protected]: original patch contained changes to the problem already handled, applied partly] |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: bound the free-cluster bitmap scan to the volume
vol->lcn_empty_bits_per_page is sized from vol->nr_clusters at mount, but
ntfs_cluster_alloc() bounds its scan of that array by the size of $Bitmap.
Those are independent on-disk quantities and the mount-time check only
rejects a $Bitmap that is too small, so an image whose $Bitmap covers more
clusters than the volume has lets the scan index past the array. A run
whose LCN lies in that gap takes the allocator straight there, since the
caller passes the file's own last LCN as its locality hint. KASAN reports
a slab out-of-bounds read when a file on such a volume is extended.
Clamp the scan to what that array covers, mirroring the max_index
calculation the mount-time scan already uses, and reject a decoded LCN
at or beyond nr_clusters in the mapping pairs decoder. Conforming
volumes are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: reject invalid empty mapping pairs
Reject an attribute with empty mapping pairs if it has inconsistent
highest VCN and size. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: reject invalid MFT LCNs from boot sector
The NTFS boot sector stores the MFT and MFTMirr locations as unsigned
64-bit LCNs, but parse_ntfs_boot_sector() decoded them into an s64.
A crafted high-bit value could therefore become negative and pass
the existing upper-bound check. The invalid value then propagated into
the MFT zone allocator and could result in an out-of-bounds access to
lcn_empty_bits_per_page. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: validate non-resident attribute offsets
ntfs_attr_update_meta() shifts the attribute name when converting between
non-sparse and sparse attributes. Converting to sparse also adds the
compressed_size field before the name and mapping pairs, requiring eight
additional bytes in the attribute record.
However, the validator does not check that name_offset is within safe
boundaries for these operations or that the additional space is available.
A malicious MFT record could set name_offset such that:
1. The name is positioned at the very end of a non-sparse attribute.
Converting to sparse would shift the name forward by 8 bytes,
writing beyond the attribute boundary.
2. The name overlaps with the mapping pairs, causing corruption during
conversion.
Add validation to ensure:
- For named attributes, name_offset is within valid bounds
- Name does not extend beyond the attribute or overlap with mapping pairs
- For non-sparse, non-compressed attributes, eight bytes are available
after mapping_pairs_offset for the compressed_size field
The space check also covers unnamed attributes, for which name_offset = 0
is valid and no name range needs to be checked. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: verify run length exceeding volume boundary
The mapping pairs decoder validates that the starting LCN is within the
volume but does not check if the run extends beyond the volume boundary.
A malformed NTFS image with a crafted mapping pairs array could cause
the kernel to access memory beyond the volume boundary, potentially leading
to memory corruption and privilege escalation.
Add validation to ensure lcn + length stays within nr_clusters. |
| In the Linux kernel, the following vulnerability has been resolved:
ecryptfs: hold msg ctx list lock when cleaning daemon queue
ecryptfs_exorcise_daemon() drops queued messages from a dying daemon
without holding ecryptfs_msg_ctx_lists_mux, but
ecryptfs_msg_ctx_alloc_to_free() requires that lock.
Take the list lock while moving the queued contexts back to the free
list to avoid racing with other global msg ctx list users. |
| In the Linux kernel, the following vulnerability has been resolved:
ecryptfs: pass packet set buffer size to parser
ecryptfs_parse_packet_set() receives a pointer into the file header, but
it calculates the remaining packet buffer size from PAGE_SIZE - 8. For
version 1 headers the packet set starts later in the header, so this can
overstate the available buffer.
Pass the actual packet set buffer length from the caller and calculate
per-packet limits from the remaining bytes in that buffer. Recompute the
remaining length after consuming a tag 3 packet before parsing the
following tag 11 packet. |
| In the Linux kernel, the following vulnerability has been resolved:
ecryptfs: reject oversized encrypted_key_size in parse_tag_3_packet
parse_tag_3_packet() set encrypted_key_size from the Tag 3 packet body
without bounding it against ECRYPTFS_MAX_KEY_BYTES (64). When
encrypted_key_size > 64, decrypt_passphrase_encrypted_session_key()
sets decrypted_key_size = encrypted_key_size and performs two
out-of-bounds writes:
1. crypto_skcipher_decrypt() writes encrypted_key_size bytes into
decrypted_key[64] via scatterlist, overflowing into the parent
ecryptfs_auth_tok struct.
2. memcpy(crypt_stat->key, decrypted_key, decrypted_key_size) writes
into crypt_stat->key[64], corrupting root_iv, keysig_list, and
mutexes in ecryptfs_crypt_stat.
Only AES-192 (cipher code 0x08) enables this because it sets
crypt_stat->key_size = 24 independently of encrypted_key_size,
allowing crypto_skcipher_setkey() to succeed while encrypted_key_size
exceeds ECRYPTFS_MAX_KEY_BYTES.
The PKI decryption path (parse_tag_65_packet) already validates
decrypted_key_size <= ECRYPTFS_MAX_KEY_BYTES; the passphrase path
omits this check.
Bound encrypted_key_size against ECRYPTFS_MAX_KEY_BYTES (64) rather
than ECRYPTFS_MAX_ENCRYPTED_KEY_BYTES (512). The 64-byte limit also
protects the 512-byte encrypted_key[] buffer, so the former 512-byte
check is removed as redundant.
[tyhicks: Adjust the code comment to refer to macros representing the
buffer sizes rather than mentioning the buffer size values since they
may change in the future] |
| In the Linux kernel, the following vulnerability has been resolved:
ecryptfs: reject too-small tag 70 packets
ecryptfs_parse_tag_70_packet() subtracts fixed metadata fields from the
parsed packet body size to derive the encrypted filename size. A
malformed packet with a body smaller than those fixed fields can underflow
that size calculation.
Reject tag 70 packets before the subtraction unless the body contains the
signature, cipher code, and at least one byte of encrypted filename data. |
| In the Linux kernel, the following vulnerability has been resolved:
ecryptfs: release message context on send failure
ecryptfs_send_message_locked() moves a message context from the free
list to the allocated list before sending the request to the userspace
daemon.
If ecryptfs_send_miscdev() fails, the context is left on the
allocated list and cannot be reused. Move it back to the free list on
failure and clear the caller's pointer. |
